If so, that would be how I would do it, which would make it fine.Īre the rear doors loud? Are the front doors loud? By using the fade/balance function I can eliminate the fronts all together, the volume is still the same and does not get "loud" until the HU is at full volume.Can you take a picture of where your gains are set on the amp (the whole side of where the gains are on the amp would help!) Sorry for the picture quality, let me know if they don't turn out and I'll try to get something better when I get home tonight. The aftermarket amp has RCA's coming from the pac to give it its signal? The amp then runs the speaker wire back to the factory amp area and ties into the speaker output (the speaker wires are cut at the factory amp and then connected to the aftermarket amp)? Is this how it is ran? I assume so but don't believe he removed the center console to get at the factory amp so not sure where exactly he spliced into the wiring. The only speaker that seems to be directly wired to the new amp is the sub, installer said that he only spliced into the stock wiring for the doors which did not eliminate the center and tweets. The 4 doors are then ran off of the focal amp as well as the sub. I was surprised to still hear the center and pillar tweeters working. I was under the impression after speaking with the installer that these would no longer be used / powered by the new amp and only the 4 new door speakers would be hooked up. So you have the tweeters and center ran off of the factory HU power. The shop that did the install blew me off saying that I just have to let the speakers break in and that it would sound better in time but the lack of sound at lower than 1/2 volume tells me otherwise.Īppreciate any comments or thoughts as this is driving me nuts! I'm into this system for $3K so far and think I would have been better off with just a speaker upgrade. Should the 4 channels be wired independently of the stock amp or is it acceptable to splice into these wires? I read somewhere that by keeping the factory sony amp in line and powering the "other" speakers you would effectively be robbing the 4 door speakers of power, is this correct? My concern is that I will cause damage to the new amp if I'm always running it at almost max volume. The pillar tweeters and center speaker in the dash are still working which made me draw that conclusion.Īt volumes less than 1/2 the music is barely audible, at 3/4 volume its comfortable to listen to and when I max out the volume its loud but not with the clarity/detail I was hoping for. Not a big deal but as a result I have lost considerable volume control at lower levels. They spliced into the factory amp I'm assuming to negate running new speaker wires to the doors. Picked up my truck and could not be more unhappy with the sound! I've never installed an amp before nor did I have any idea on how to run/splice the wiring so I decided to let the shop install these components. PAC audio AP4-FD21 Amp integration interface ( installed this myself) I thought if this upgrade sounded good than a new sub and amp should really enhance my music listening so went back to the shop I was dealing with and bought the following: Follow the accompanying instructions on how to download the files and transfer them to your USB drive.Hello, I'm a noob when it comes to car audio so please forgive me if I come across as such.įinally decided to upgrade the door speakers in my Platinum and went with the Focal 5x7 Access, what a tremendous improvement in sound over the stock ones, did this myself as it was fairly straightforward. Precision machined from 1/2-inch HDPE for a perfect fit. Focal PS 165 SF 6-1/2' component speaker system Front Door. I do understand how to connect the front and rear door speakers to the amp, i am confused about the single center dash speaker. Includes Laser Cut Foam Gasket for proper seal to the cabin. I have bought all new speakers and and a 5 channel amp to upgrade my system. (15) Key Features: - Made of high-quality HDPE plastic, CNC Machined in-house. When you have the USB drive ready, insert it into to your computer and choose Start Download Process. Factory Subwoofer Block Off Plate for Rear Wall (Includes Unleashed) - Required for the 2021-2024 Ford F-150 B&O. Locate an empty USB drive that has at least 2 GB of free space and is not password protected.If you see the notification, "You have an update available," choose Download SYNC Update Locate an empty USB drive that holds 2 GB or more of data and is not password-protected.Activate your SYNC Owner account (if you haven’t already done so), by logging in and registering your vehicle.Afterwards, be sure to report the successful installation. You can then install the update in your vehicle. Download the latest SYNC ® with MyFord Touch™ software update to a USB drive at no charge.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |